Cremation Urn An Unusual Turning

Cremation Urn An Unusual Turning More Woodworking Projects

Cremation urn an unusual turning is article about More Woodworking Projects bookmarked by miguel with ID 11455554143 was uploaded on 20-02-2019 and has been viewed 172,749 times.

Every once in a while, an unusual woodworking commission comes along.This recently happened to me when I was asked to turn a cremation urn in the shape of a Shriner fez.Here's the project.Hope you can get some ideas and tips for your own projects.

Material Selection.Since a fez is red and I'm not a big fan of staining wood if I can avoid it, I chose Honduras Mahogany for the turning.In addition to being the right color, it's an easy wood to turn.

I also knew I'd be able to get wide pieces.This was important, since I needed a 9″ x 9″ x 10″ blank.I was hoping to simply face glue pieces in order to get the size I needed, without having to edge glue them first.

I was able to send the mahogany through my surface sander and face glue five pieces to get the dimensions I needed.I chose walnut for the base, knowing that the richness of the walnut would really stand out against the mahogany.

Dimensions.While the mahogany was in clamps, I worked on final dimensions for the project.I had been told that the cremains would fit into a conventional fez,...

Read More →

Disclaimer: images, articles or videos on this website sometimes come from various other media sources. Copyright is fully held by the source. If there are problems related to this, you can contact us on this page.
Bookmark ID: 11455554143

Cremation urn an unusual turning is just one of the many collections of bookmark on this website. There are approximately 511 posts that exist in our database associated with this article. Here are the details of "cremation urn an unusual turning" article:

Category:
Title:
Image URL:
Post URL:

This is a post related to cremation urn an unusual turning, there are approximately 511 article related to this more woodworking projects category. Please see the details below and click on the title for more information..

Turning Project If You Want To Take Your Hollow Turning To The Next Level To Create Something Unique This Approach Will Intrigue You And Don T Stop Here Try Your Hand At Creating An Eight Sided Vessel Or Possibly Cut The Turning Across The Grain Rather Than With The Grain Magazine 150 x 100

Turning Project If You Want To Take Your Hollow Turning ...

Turn a Four-Sided Hollow Vessel Photos by Trent Watts INFO: DIFFICULTY - 3/5, LENGTH/TIME - 3/5, COST - 2/5 Have you ever wondered how to make a four-sided hollow turning? After making many hollow turnings of various sizes and shapes I wanted to add the effect of making one with ... Turning project if you want to take your hollow turning to the next level to create something unique this approach will intrigue you and don t stop here try your hand at creating an eight sided vessel or possibly cut the turning across the grain rather than with the grain is post about Magazine bookmarked by marc with ID 11437709077 was uploaded on 28-03-2019 and has been viewed 315,137 times.

Turning Project Use Your Lathe To Turn An Offset Platter With Wave Like Undulations On Its Surface It S Easier Than You D Think Magazine 150 x 100

Turning Project Use Your Lathe To Turn An Offset Platter ...

Turned Wave Platter Photos by Lisa Chemerika (Lead Photo by Rob Brown) This project started, like most of my projects, by someone telling me I couldn't do it on a lathe.As we all know, lathes rotate wood that is centered on a chuck, and you can only cut away wood ... Turning project use your lathe to turn an offset platter with wave like undulations on its surface it s easier than you d think is bookmark about Magazine bookmarked by milton with ID 11020308640 was uploaded on 18-04-2019 and has been viewed 178,675 times.

Turning Project This Is An Easy Project That Is A Great Spindle Exercise You Can Make It An Elaborate Piece With Multiple Woods As Shown In This Article Or You Can Make It From One Piece Of Wood Magazine 150 x 100

Turning Project This Is An Easy Project That Is A ...

Ring Stand The shape is what really dictates the outcome of the piece.With this particular piece I used flexulosa burl for the base, with a mid-section of African blackwood, and French boxwood for the spindle.Flexulosa is a beautiful wood that comes to us from a range of small pacific islands ... Turning project this is an easy project that is a great spindle exercise you can make it an elaborate piece with multiple woods as shown in this article or you can make it from one piece of wood is bookmark about Magazine bookmarked by ronald with ID 12453684975 was uploaded on 10-02-2019 and has been viewed 393,603 times.

Turned Furniture This Well Proportioned Small Early 18Th Century Candlestand Table Presents An Interesting And Easily Made Turning Project Magazine 150 x 100
Turned Furniture This Well Proportioned Small Early 18Th Century Candlestand ...

Candlestand Table Illustrations by Lee Gabel Stock SelectionAlthough this table is made of walnut, other hardwoods such as cherry, mahogany, beech, maple, etc., would be quite satisfactory.Softwood is not recommended for this project.Construction is straight forward.The legs and stretcher are simple turnings, the feet are shaped with a band saw ... Turned furniture this well proportioned small early 18th century candlestand table presents an interesting and easily made turning project is bookmark about Magazine bookmarked by gabriel with ID 13094039716 was uploaded on 20-01-2019 and has been viewed 396,722 times.

Wood Turning Most Ceiling Fans And Many Lamps Come With Lower Quality Machine Turned Pulls They Are Practical But They Are Often Far From Attractive So Why Not Replace Those Pulls With An Attractive Piece Made From Turned Exotic Wood Magazine 150 x 100
Wood Turning Most Ceiling Fans And Many Lamps Come With ...

Lamp Pulls You could use up those small bits of wood that you have been saving.You know the ones: they are too small to use, but too beautiful to throw away.Now you can use them to create decorative lamp pulls.This simple project can take you as little as half an ... Wood turning most ceiling fans and many lamps come with lower quality machine turned pulls they are practical but they are often far from attractive so why not replace those pulls with an attractive piece made from turned exotic wood is article about Magazine bookmarked by john with ID 13060917741 was uploaded on 07-04-2019 and has been viewed 216,457 times.

Wood Turning This Project Is Both Elegant And Economical I Say That Because These Earrings Are Turned As One Piece Then Cut Into Two And Shaped Off The Lathe The Project Requires A Bit Of Off Set Turning With An Eccentric Chuck Magazine 150 x 100

Wood Turning This Project Is Both Elegant And Economical I ...

Two Earrings, One Turning The eccentric chuck allows a true centre to be manipulated to produce off-set centres.On the eccentric chuck, (photo 1) the 'face-plate' is in a slot.Move the faceplate from centre (off-set it) to the extreme edge of the eccentric chuck, by turning the set-screw on the side.Essentially ... Wood turning this project is both elegant and economical i say that because these earrings are turned as one piece then cut into two and shaped off the lathe the project requires a bit of off set turning with an eccentric chuck is post about Magazine bookmarked by adam with ID 11767993543 was uploaded on 16-03-2019 and has been viewed 360,703 times.

Wood Turning This Issue We Turn A Shallow Natural Edged Dish With An African Blackwood Foot This Particular Piece Of Mallee Is Turned From A Spectacular Specimen From Australia Magazine 150 x 100

Wood Turning This Issue We Turn A Shallow Natural Edged ...

Burl Platter The Mallee burl can be found in only a few places around the world such as relatively dry areas of Australia, the Eyre Peninsula and western New South Wales, to isolated areas of Central Queensland.Because the wood is very rare, only a small amount of this wood is ... Wood turning this issue we turn a shallow natural edged dish with an african blackwood foot this particular piece of mallee is turned from a spectacular specimen from australia is article about Magazine bookmarked by alberto with ID 1463208376 was uploaded on 23-01-2019 and has been viewed 59,128 times.

Turning Project The Great Thing About Box Making Is That It Can Be A Good Way Of Using Up A Small Piece Of Wood Even An Offcut That Might Otherwise End Up Being Discarded It Can Be Transformed Into A Thing Of Beauty Using Your Imagination Originality And Skill Magazine 150 x 100

Turning Project The Great Thing About Box Making Is That ...

Making Turned Boxes Photos by Steven Kennard INFO: DIFFICULTY - 2/5, LENGTH/TIME - 2/5, COST - 1/5Required Tools: Smooth dovetail jaws in a scroll chuck 1/16" parting tool 1/4" gouge for hollowingSmall skew chisel (1/2" or smaller)Small round-nosed scraperVinyl electrical tapeVernier callipersMethod of holdingMost species of wood can be used ... Turning project the great thing about box making is that it can be a good way of using up a small piece of wood even an offcut that might otherwise end up being discarded it can be transformed into a thing of beauty using your imagination originality and skill is bookmark about Magazine bookmarked by clinton with ID 12296651109 was uploaded on 23-03-2019 and has been viewed 118,111 times.

Turning Project One Of The Most Popular Items To Make When You Decide To Take Up Woodturning Is A Lidded Box This Turned Box Is An Excellent Study Of Different Techniques To Add To Your Repertoire Magazine 150 x 100

Turning Project One Of The Most Popular Items To Make ...

Lidded Jewellery Box Tools and Supplies The most popular use for these boxes is for keeping jewellery.However, they can be used for many different purposes, from holding paper clips, to pills in a lady's purse.They make excellent gifts and usually become a treasured possession of the recipient.An assortment of shapes, ... Turning project one of the most popular items to make when you decide to take up woodturning is a lidded box this turned box is an excellent study of different techniques to add to your repertoire is article about Magazine bookmarked by fernando with ID 12176328710 was uploaded on 09-01-2019 and has been viewed 411,643 times.

Turning Project Once In A While A Tool Handle Breaks Maybe From Excessive Blows With A Mallet Or Perhaps You Have Purchased A Tool But The Original Handle Just Doesn T Feel Right Whatever The Reason Making A New Tool Handle Is An Enjoyable Process That Provides You With The Opportunity To Further Develop Your Design Skills Magazine 150 x 100
Turning Project Once In A While A Tool Handle Breaks ...

Custom Tool Handle Illustration by James Provost Common handle styles I chose to replace the handle of a small bench chisel.The chisel has a sleeve style fitting as opposed to a tang that is inserted into the handle.I decided to use Jatoba (a.k.a.Brazilian cherry), a very hard and dense timber ... Turning project once in a while a tool handle breaks maybe from excessive blows with a mallet or perhaps you have purchased a tool but the original handle just doesn t feel right whatever the reason making a new tool handle is an enjoyable process that provides you with the opportunity to further develop your design skills is bookmark about Magazine bookmarked by sean with ID 12616989317 was uploaded on 08-01-2019 and has been viewed 367,396 times.

Cremation Urn An Unusual Turning More Woodworking Projects 150 x 100
Cremation Urn An Unusual Turning

Every once in a while, an unusual woodworking commission comes along.This recently happened to me when I was asked to turn a cremation urn in the shape of a Shriner fez.Here's the project.Hope you can get some ideas and tips for your own projects.Material Selection.Since a fez is red and ... Cremation urn an unusual turning is post about More Woodworking Projects bookmarked by raymond with ID 11455554143 was uploaded on 20-02-2019 and has been viewed 172,749 times.